FCC油浆提高废胶粉改性沥青热存储稳定性试验

废胶粉用FCC油浆进行预处理后用于沥青改性,制备出沥青与胶粉间相容性好、高温存储性能稳定的胶粉改性沥青.考察并得出相关工艺条件,同时应用多种评价手段分析改性后沥青的性能,结果表明,预处理后胶粉改性沥青的高温存储性能稳定,低温时柔韧性、抗开裂性能明显提高,高温时稳定性、抗车辙能力及弹性回变性能增强,沥青粘弹区间明显变宽.     

复合固体超强酸SO42-/Fe2O3-γ-Al2O3催化合成丁酸丁酯

采用沉淀硫酸化法制备了复合固体超强酸催化剂SO2-4/Fe2O3-γ-Al2O3,确定了其最佳制备工艺条件:硫酸浸渍浓度为0.6 mol/L,浸渍时间4 h;焙烧温度550℃,焙烧时间3 h.并采用该催化剂合成丁酸丁酯,考察了物料配比、催化剂用量和反应时间对酯化反应的影响,确定了丁酸丁酯的最佳合成条件:丁醇与丁酸摩尔比为1.4:1,催化剂用量0.9%(以反应物质量计),回流条件下反应3.0 h,在此最佳合成条件下,酯化率可达95.6%.     

Profile-Driven Component Placement for Cluster-Based Online Services

The growth of the Internet and of various intranets has spawned a wealth of online services, most of which are implemented on local-area clusters using remote invocation (for example, remote procedure call/remote method invocation) among manually placed application components. Component placement can be a significant challenge for large-scale services, particularly when application resource needs are workload dependent. Automatic component placement has the potential to maximize overall system throughput. The key idea is to construct (offline) a mapping between input workload and individual-component resource consumption. Such mappings, called component profiles, then support high-performance placement. Preliminary results on an online auction benchmark based on J2EE (Java 2 Platform, Enterprise Edition) suggest that profile-driven tools can identify placements that achieve near-optimal overall throughput.     

Monte Carlo simulation of gas phase polymerization of 1,3‐butadiene. Part II: Kinetics optimization and confirmation

Studies on the deactivations and initiations of gas phase polymerizations of 1,3‐butadiene have been achieved by Monte Carlo simulation. Initiation and deactivation control the reaction before and after the peak of the polymerization rate, respectively. The influence of polymerization temperature has been studied. Monte Carlo modeling of polymerization kinetics and mechanism was confirmed by the agreement of experimental data and simulation results of polymerizations run with a temporary evacuation of monomer. The balance of catalysts and active chains is established by both initiation and chain transfer reactions with cocatalyst, which causes a ‘pseudo‐stability’ stage. © 2003 Society of Chemical Industry     

基于EAP/RADIUS的WLAN认证和密钥分配协议

研究了无线局域网的认证机制,描述了EAP/RADIUS协议在IEEE802.1x标准中的消息封装格式,针对基于端口访问控制协议的缺陷,提出一种新的应用于WLAN的认证和密钥分配方案,并设计详细协议流程.该协议基于EAP/RADIUS认证框架,使用服务令牌将认证和授权结合起来,授权校验的同时进行密钥分配,完善了WLAN的访问控制机制.     

Characteristics of low-leakage deep-trench diode for ESD protection design in 0.18-/spl mu/m SiGe BiCMOS process

This paper proposes a novel low-leakage BiCMOS deep-trench (DT) diode in a 0.18-/spl mu/m silicon germanium (SiGe) BiCMOS process. By means of the DT and an n/sup +/ buried layer in the SiGe BiCMOS process, a parasitic vertical p-n-p bipolar transistor with an open-base configuration is formed in the BiCMOS DT diode. Based on the two-dimensional (2-D) simulation and measured results, the BiCMOS DT diode indeed has the lowest substrate leakage current as compared to the conventional p/sup +//n-well diode even at high temperature conditions, which mainly results from the existence of the parasitic open-base bipolar transistor. Considering the applications of the diode string in electrostatic discharge (ESD) protection circuit designs, the BiCMOS DT diode string also provides a good ESD performance. Owing to the characteristics of the low leakage current and high ESD robustness, it is very convenient for circuit designers to use the BiCMOS DT diode string in their IC designs.     

不同注F剂量与CMOS运放电路辐照损伤的相关性

在不同注F剂量条件下,对P沟和N沟两种不同差分对输入CMOS运放电路的电离辐照响应进行了研究.分析比较了注F和未注F运放电路电离辐照响应之间的差异.结果表明,在栅场介质注入适量的F,可有效抑制辐照感生的氧化物电荷尤其是界面态的增长,从而提高CMOS运放电路的抗辐照特性.     

以3D软件应用为中心的设计管理模式——PDS在配管设计中的应用

由PDS的特点入手,结合工程实践的应用情况,阐明了3D软件可以更广泛的应用于配管的设计中,强调了以3D模型为中心开展设计和管理的新模式.     

GMSK无线接收终端设计

设计了GMSK(Gauss Minimum Shift Keying，高斯最小频移键控)无线接收终端的硬件与软件系统。硬件的射频电路对空中信号进行接收与滤波，再由以MX589构成的解调模块解调，输出数字信号；数字硬件以单片机GMS97L5为核心。软件系统设计了对IC卡AT88SCl608加密卡的认证以及对串行数据的接收与处理的中断程序。终端系统接收数据快、性能稳定。     

软印刷技术

软印刷技术是基于弹性体印章/模具来转移图形结构的微纳加工技术。详细介绍了软印刷技术中转移图形结构的多种方式,并探讨软印刷技术在微纳电子学、光学、传感器、生物等领域的广泛应用。对软印刷技术的弹性体印章/模具制备、聚二甲基硅氧烷的属性、理论研究等进行了探讨。